Installation drawing their own hands: how to fix?

Everyday cooking is not the best way affects the kitchen environment. Fumes, steam and odors spread throughout the room, leading to the wrong kind of furniture and equipment. Suffer from moisture vapor walls and ceiling - as a result of the room gets quite unsightly. Get rid of such troubles, a simple extraction installation. To connect a device that does not need to be a highly qualified specialist, enough to arm the necessary tools for installation, examine the installation of the foundations and the problem will be solved in a short time. To secure the job as much as possible, it is important to know the features of the earth and how fasten the device to the wall.

Different types of hoods

In order to properly mount the suction unit should be familiar with the typical features of the selected unit:

• Hanging flat model, installed above the stove. Attach them to the wall, you can use the massive anchor-nails. Recirculation device has many models allows you to use the device without connecting to the ventilation output.
• Recessed model perfectly fit into the small kitchen through fastening to the cabinet and comfortably settle down over the stove. Grease filter allows it to operate normally without air.
• Dome devices are the most stylish and comfortable, high suction power noticeably increases their price.

Attention! buying the hood for the kitchen, You need to make sure there is recycling. Lack of ventilation duct over the stove will not allow drawing work in full mode.

In addition, the grease filters need constant replacement. Avoid these costs will allow periodic cleaning of the product. For their complete drying requires 1 or 2 days.

work especially

Depending on the mode of ventilation hoods are of the following types:

• Flow mechanisms established over the stove, pushed a cloud contaminated vapor in the ventilation hole, which ensures high productivity.
• Purified air circulation device installed due to the filter housing. Connection to the ventilation is not required. Such extraction installation in the kitchen is simple, however, the cleaning result would be significantly reduced.

In the process of buying the hood it is necessary to check the efficiency of cleaning. According to specifications, the air must be renewed every 12 hours. According to these indicators calculated suction power.

It is important that the noise level of work included instruments differs significantly, this figure should be well studied. The value of 50 dB is too high, it is best to choose a silent exhaust, as well as sound-absorbing inserts model.

Security will not prevent

To mount the hood with his hands, it is important to remember personal safety when working with electricity. electric shock The probability increases with the humidity over the stove or improperly connected to the network. Secure the device will help correct grounding and a clear three-wire connection cables. Euro sockets already provided its structure a secure connection. Special grounding terminal allows to fix the corresponding conductive with the device, denoted colored stripes or inscription Ground.

If such a device for the electrical connection is not provided in the apartment, you can make your own hands, by connecting to the neutral conductor. You can find it in the electrical box, it usually takes the form of the finished pin, immured in the wall. Then he pulled into the kitchen and fixed to the hood by means of a separator machine.

Attention! If, nevertheless, the apartment has a connection to the earth and neutral wires, do not touch them: danger of electric shock is too high.

Attaching the Hood

Installation kitchen hood is determined by its structural features. The easiest and surest way is to install on the wall.

1. Mark the attachment point between the hood and hob. The optimum height of 50-80 cm. Otherwise, the absorption efficiency of recycled air is reduced to zero.
2. With the appended drawing measure 4 tags.
3. Perform the drill hole over a plate of 8 mm.
4. Screw the screws for future hanging on them drawing.
5. Secure the device and insert the additional fastening of the plate.

Tip: almost all products have a detailed connection instructions, if it is missing, you can seek help from the Internet.

Features duct installation

The process requires the installation duct corrugations desired diameter and length (60 cm to 3 m), the clamp, the vent hole. Fixed to the wall outlet must be of the same diameter as the pipe itself and the opening for exhaust air. To get the most airtight connection, it should be reserved sealant and masking tape.

Types of air ducts:

• Plastic - the strongest light, emit virtually no noise thanks to the smoothness of the inner surface.
• Corrugation of aluminum - the simplest material that easily accepts any configuration. The main advantage of the inclined pipe is a silent mode of its operation.

To the duct properly perform their duties, it is not recommended to narrow, otherwise may disrupt its integrity. Particularly dangerous for brittle material sharp bends. If the tube is broken, it can seal a conventional tape, however, after such repair work drawing changes. Tilt the device is unlikely to be able to fully perform their duties.

Cope with the installation of chimney hoods themselves

To their hands to put the hood over the fireplace, use the vent. To do this, the throttle valve must be put on the air channel and provide it with a reliable seal. During idle device valve overlap, so that the heat out of the house did not go away in the street. Air valve fireplace installation should not go to the basement. So it will be able to avoid the accumulation of bad air in the room.

Tip! Attach the duct it is advisable to windy side: air vacuum will help the best way to pull odors from the house.

Set the correct hood with his hands, ventilation is provided superb performance. It carefully controls the temperature of the effluents, which must be within 80 degrees. Increase of these indicators will cause overheating of the body, which is very dangerous for the occupants of the house. Fireplace hood to meet all safety requirements, it should be possible to accurately calculate the parameters of existing cross-sectional area of ​​ventilation outlets.

Advantages:

• High speed and simplified assembly diagram;
• an extensive area of ​​use;
• perfect replacement of traditional chimney;
• rapid removal of dust and dirt out of the premises;
• Installation at any point;
• elimination of any unpleasant smells;
• low cost of the device.

The presence of several modes of operation inherent in virtually all modern fireplaces.

Tools required for operation:

• punch;
• screwdriver;
• measuring instruments;
• hammers of different sizes;
• dowels, screws.

How to install the fireplace hood:

1. Accurately determine the sizes of future devices.
2. The attachment points for drawing a horizontal line mark.
3. Mark the location of fasteners.
4. Drill hole depth 50 mm.
5. Secure the dowels in the finished frames.
6. Hang the hood on the fixtures.
7. Check the strength of the fixation device.
8. The remaining 2 screws to screw through the rear wall panel.

So, to mount the hood with his hands is a snap, just need to be patient, accuracy and diligence. Further operation of the device will be connected with the periodic cleaning of soot and grime, twice a year is sufficient. In this simple way will avoid accidental ignition.