Ideal slopes of PVC with the use of liquid plastic Cosmofen

Liquid plastic for PVC windows is basically a glue-sealant. Its use is necessary when finishing the joints of window units. The advantage over the sealant is that it does not burn out and flake off the window. You can work with liquid plastic with any polymer surfaces. It is very resistant to ultraviolet rays. Due to the ideal combination of solidified parts, the visibility of a single window with a slope is created. Such gluing is obtained as a result of diffusion welding, which ensures the interchangeability of the materials of the parts.

The visibility of the integral window and slope design allows a combination of individual solidified parts. The optimal result will help to achieve the use of diffusion welding technology, which will later allow replacing individual sections, rather than the entire structure as a whole.

Application of the composition for the slopes

When installing plastic windows of any complexity, one way or another, it becomes necessary to install slopes. This need arises due to deformation of the old window opening as a result of carrying out the necessary works aimed at dismantling the old window. Also, a slope is needed to maintain the temperature inside the room due to the reduction of the thermal losses of the window.

To make a slope use a special adhesive for PVC windows. Liquid plastic. To perform all the necessary functions, the slope must have a number of specific properties and at the same time have a presentable appearance. Due to the similar structure of PVC windows and liquid plastic eventually form a fairly solid, monolithic part. The seam made of liquid plastic has increased resistance to various mechanical damages and is completely safe, environmentally friendly material. The use of liquid plastic for PVC windows also contributes to improving the noise of the insulation layer, which will protect any room from extraneous sounds from outside, dust and dirt and give aesthetic appearance.

Cosmofen and Cosmofen plus what is the difference

These varieties of liquid plastic have a one-component base of reduced viscosity, while the material remains exceptionally transparent. It has a fast adhering effect, therefore it is recommended to use parts that have no defects on the surface. Such material as liquid plastic Kosmofenpolepolzuetsya considerable popularity in the field of repair and personal services for conducting assembly works of any complexity, both in scale production, and in repairs.

Some features of using liquid plastic Cosmofen

• high resistance index;
• resistance to sudden temperature changes;
• low heat loss.

Efficiency of use

Liquid plastic, the instruction to which is not always read by users, will not cause difficulties in use. Before applying the glue, the surfaces are rid of all kinds of dirt and dust. Then, the surfaces are thoroughly dried. From the quality of preparation, the entire result of gluing depends. Liquid glue is applied extremely neatly, smoothly over the entire joint. After 15 minutes, the glue dries up and becomes hard.

It is important to know that when hardening liquid plastic decreases in volume and the seam turns out to be more retracted.

Main characteristics of the sealant Cosmophen:

• optimum temperature regime ranges from +20 to +5 degrees;
• for solidification with glue will be enough for 5 minutes, while for full hardening it will take a bit more than a day;
• for achieving the optimum result, the humidity of the air in the working room must be at least 60%;
• the properties of the liquid plastic are preserved for a couple of minutes after the application of the mass on the work surface;
• to expend liquid plastic cosmofen adopted in the ratio of 150g / m2.

Cosmofen plus is used for installation works: sewage, sanitary ware, outdoor advertising and aluminum structures of any complexity.

Advantages of the adhesive sealant Cosmofenplus:

• accelerated polymerization;
• resistance to sudden temperature changes;
• increased resistance of the material to ultraviolet rays.

Widget from SocialMart

Technical features and characteristics:

• polymer adhesive base is located directly in the solvent;
• impact-tough property of the glue in a solid state;
• the optimum working temperature in the working room is from +5 degrees Celsius;
• for lasting adhesion is quite a few minutes. The best effect can be achieved with the help of an additional load;
• the glue will completely solidify within 24 hours.

Tips for using the sealing glue Cosmofen plus

First, the surfaces to be bonded are cleaned from dust, moisture and various construction debris. It is recommended to apply the adhesive evenly over the entire surface. The connection of the parts takes no more than a minute, and one more is required to freeze. Liquid plastic Cosmofen plus is not used for bonding pressure pipes. Store the sealant sealant in a well-closed container. The shelf life of the material at a temperature of 15 to 30 degrees is one year. During the entire storage period, there may be a slight increase in the viscosity of the adhesive.

Safety precautions for working with liquid plastic

Liquid plastic based on a dangerous element of cyanoacrylate, when using a sealant, certain precautions can not be neglected, such as:

• to people with a tendency to allergic manifestations, it is not recommended to use this product;
• Adhesive or liquid plastic should only be used with gloves while following other mandatory precautions;
• at the end of work should be well ventilated room;
• , to avoid inhaling the vapor of the sealant glue, it is required to wear a mask.

How to make slopes yourself

The technology of using such material as a glue for PVC windows is liquid plastic, does not belong to the category of complex ones, so it will not be difficult to mount slopes. All the necessary tools and materials are purchased at any construction shop. From the tools you will need: an adhesive tape, a stationery knife, a simple pencil and a square. Necessary materials: mounting foam, liquid nails, slopes and liquid plastic.

Sequence of actions during assembly works independently:

• mounting edge made, from the mounting foam is cut along the perimeter of the window;
• produced the necessary measurements of the width and length of the slope. The results are transferred to the surface using a simple pencil;
• panel is cut out based on measurements, and then inserted by a narrow edge into the groove located at the top. This will allow you to notice even the slightest error when the dimensions of the panels do not coincide;
• liquid nails or mounting foam applied to the inside of the slope with a snake, after which you can insert the panel into a special groove on the wall;
• for additional strength, joints are fixed with adhesive tape;
• the same actions need to be done with the rest of the slopes. To achieve the maximum result, it is necessary to remove all the slots at the joints with the panels;
• after a few hours all the panels are glued together;
• liquid plastic must be squeezed out very neatly and only at the joints themselves. Surplus is removed immediately with a sponge or non-colored fabric;
• scotch is cleaned the next day.

The last step is to glue the decorative corners with a cut at 45 degrees. Elements are glued with the help of glue-sealant . Corners temporarily glue with adhesive tape around the perimeter. Painting Scotch tape can be easily removed the next day, without any difficulties. Liquid plastic can go through the joints of corners, which will make the plastic joint corners cast. Thanks to the cosmofen the window slope looks one whole with a window.